Summer Starts Here - Save up to 70%
Draw-Tite 7-Way Pre-Wired Car Connector Installation - 1993 Dodge Ram Pickup- Video
Today we're gonna be taking a look at the Tow Ready 7-pole Wiring Kit. And all you really need to do is just go on our website and use that FitGuide at the top, put in your vehicle's year, make and model and that's gonna get you set up with the correct kit for your specific vehicle. Today we have a 1993 Dodge Ram 250 and we're gonna be taking a look at the Tow Ready 7-pole Connecting Wiring Kit. What we're gonna get with the kit, of course, our connector and the wiring, it's gonna be about seven foot long. We have a little flap and it's spring loaded. So it's gonna close shut even if you forget to close it. more
3/10/2022 11:08:18 AM
EZ Connector Magnetic 7-Way Trailer Connectors Installation - 2005 Dodge Ram Pickup- Video
Speaker 1: Today on our 2005 Dodge RAM 3500, we're going to be doing an installation of the EZ connector magnetic T connector with seven way trailer connector. Part number 319-R7-06D.Upgrade your RAM to work with the magnetic EZ connector seven ways. This is going to allow you to have a standard seven way connection on a trailer that has a magnetic EZ connector. It's a face to face connection. There are no pins, or blades to break or bend. The magnetic connection is strong enough to hold it in place, but it's easy to disconnect when needed.It's going to allow you to maintain the factory seven way connection on your RAM, so you can still tow trailers with standard seven way connectors. more
3/19/2018 4:42:09 PM
Trailer Wiring Harness Installation - 2001 Dodge Ram Pickup- Video
Today on our 2001 Dodge Ram pickup, we're going to review an install, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part number C55329. Now to begin our install, we need to find the wiring behind the tail light assemblies. Behind the driver's side tail light assembly and just below the pickup bed is the manufacturers wiring that goes into the tail light assembly. We need to separate these two connectors. To do that, we'll press on the locking tab and simply separate the two. Next, we'll move over to the passenger side and repeat the same process. We're now ready to begin installing the new Curt T-connector wiring harness. On the passenger's side, we're going to use the white and green wire T-connector. more
6/23/2015 2:36:39 PM
Trailer Wiring Harness Installation - 2003 Dodge Ram Pickup- Video
Today on our 2003 Dodge Ram pickup, we'll be installing the Hopkins Endurance 5th Wheel/Gooseneck 90-degree wiring harness with 7-pole trailer connector, part number HM42137. To begin our install, we're going to start in the pickup bed. We're going to find a suitable mounting location for our 7-pole plug. Once we find our location, which we're going to go here in the pickup bed side wall behind the wheel well and in front of the rear stake pocket, then we can take our hole saw and drill out our 2 1/8" hole as per the instructions. Once we have the hole drilled out, we can move underneath the vehicle and feed our 7-pole connector up through the hole. Another option while you're already in the pickup bed, is to take the vehicle connection end or T-connector and feed it down. more
1/5/2015 1:30:12 PM
Trailer Wiring Harness Installation - 2004 Dodge Ram Pickup- Video
Today on our 2004 Dodge Ram Pickup 2500 Series Quad Cab we're going to be installing the Hopkins Endurance Fifth Wheel and Gooseneck 90-Degree Wiring Harness with a seven-pull plug. Part number HM42137. To being with, we're going to need to choose a location in our bed to mount our seven-way plug. Now we've already gone ahead and checked underneath the bed to see where we drill our hole to make sure that there's nothing behind it that could be damaged. Now, with this being a short bed and it having a bed liner, we will need to do some extra trimming on the bed liner to allow our seven-way plug to fit against the metal. We'll go ahead and first use our hold saw to drill our hole for the plug itself. Next we're going to need to trim some of the extra bed liner away. Go ahead and put our thing up in there, make a couple marks. more
9/4/2014 11:37:09 AM
Trailer Wiring Harness Installation - 2006 Dodge Ram Pickup- Video
All right. Today, on our 2006 Dodge Ram pick up, we'll be installing the Hopkins Endurance 5th Wheel Gooseneck 90 Degree Wiring Harness with a 7 Pole Plug, Part Number HM42137. To start off, we'll get in the bed of the truck and we'll go ahead and find a location for our 7 pole connector. This is largely a personal preference. In this case, we're going to go ahead and mount it towards the tailgate. Once we're satisfied with our location, we'll go ahead and drill out the quarter inch pilot hole. Then, we'll go back at it with the hole saw. more
8/5/2014 9:31:12 AM
Hopkins Endurance Fifth Wheel Wiring Harness Installation - 2011 Dodge Ram Pickup- Video
All right, today on this 2011 Dodge Ram pickup, 3500 series crew cab, we're going to install part number 41157. This is a Hopkins Endurancefifth wheel wiring harness, with a seven pole connector. OK, to start off our install, we need to find a location for our socket that we're going to install in the bed. Once we have that planned out, we'll go ahead and drill a quarter inch pilot hole Then we'll go back at it with a two inch hole saw OK, once we have our hole made, we'll go ahead and take our wire harness and run it through the hole. Well take the one end with the two connectors and go ahead and push it through the hole, and then let it fall out the bottom, then push the rest of our slack in place. OK, and then we'll save the other end to install into our seven pole connector We'll put some of the supply unintelligible 00:00:49 grease onto the terminals on the inside edge, then snap the two halves together. OK, once we have them together, we can go ahead and put the seven pole connector into the hole. And then we'll go ahead and use the provided hardware to attach it to the bed. Now the hardware is four self-tapping screws and washers. We'll position our seven pole connector, and then install our screws one at a time. We leave them loose until we have them all installed, and then we'll go ahead and tighten them down for good. All right, now go underneath the bed of the truck, and we'll go ahead and route our wire harness towards the bumper and towards the back side of the bumper where pre-existing seven pole connector is. Now we need to go ahead and disconnect the seven pole from the wire harness. We'll push down there's a small tab that we need topush down, and then we can go ahead and separate the connector from the wires. We'll let that go for now, and then we'll go ahead and take our new Hopkins wire harness and we'll get it ready to plug in the two halves. We'll go ahead and add the remainder of the unintelligible00:01:41grease on the terminals, and then just plug the two matching ends together. Again , we want to make sure everything remains snapped, so we know we're secure. OK, then we'll go ahead and take our extra length of wire and go ahead and route them up and out of the way, and secure them with some zip ties. One last thing is the white wire from the ring terminal.We need to ground that to the frame, so we'll go ahead and use a self-tapping screw to do that. In this case, we'll be using a number fourteen self-tapping screw. And with that, that will finish up our install of the Hopkins Endurance fifth wheel ninety degree wiring harness, with the seven pole plug, on our 2011 Dodge Ram pickup, 3500 series truck. . more
11/13/2013 1:53:52 PM
Fifth Wheel and Gooseneck Wiring Harness Installation - 2010 Dodge Ram- Video
Today on our 2010 Dodge Ram pickup, we'll be installing the Pollak fifth wheel gooseneck T connector, part number PK11893-11932. First, let's go ahead and identity where we'll be mounting our 7-pole. Here on the inside of the bed, just behind the driver side wheel well, is a great location. Now before drilling out the large hole, we'll go ahead and use a smaller bit for a pilot hole, and then double check the location. Next, we'll go ahead and drill it out to the larger size, using our larger hole saw bit as per the instructions. Now with the hole drilled out, we're ready to go ahead and start routing our wire. more
7/24/2013 9:16:19 AM
Fifth Wheel and Gooseneck Wiring Harness Installation - 2005 Dodge Ram- Video
Today on our 2005 Dodge Ram Pickup, well be installing the Bargman 5th Wheel Gooseneck 90 Degree Wiring Harness with 7-Pole plug, part number 51-97-411. To begin our install, well first locate in the pickup bed where well be mounting our 7-pole, then using a smaller bit for our pilot hole, once weve located a spot well go ahead and drill our hole. Well go ahead and drill out using the two inch hole saw as recommended per the instructions. Now with the large hole drilled out, well go ahead and feed half of our T-connector through the hole then our other plug followed by the remainder of the wire until our 7-pole mounts flush with the bed. Then using the self-tapping screws provided with our install kit, we can go ahead and secure the 7-pole plug to the bed side. Next well get underneath the vehicle and start routing our wire over to the back of the bumper where the manufacturers wiring meets the bumper. Here at the back of the bumper, well go ahead and disconnect the manufacturers wiring from the back of the 7-pole plug at the bumper. more
4/3/2013 2:54:45 PM
Fifth Wheel and Gooseneck Wiring Harness Installation - 2012 Dodge Ram Dually- Video
Today on our 2012 Dodge Ram 3500 dual rear wheel, we'll be installing the Pollak fifth wheel goose neck T-connector with seven pull, part number PK11893-11932. First, we'll go ahead and locate a suitable location for our new seven pull connector. Here, just behind the rear wheel on the driver's side is a common position. Go ahead and locate the area, check underneath to make sure there are no obstructions, and then we'll go ahead and use a small pilot hole and drill it out. This will allow us to again get underneath and double check where the pilot hole location is and correspond it's where our seven pull connector will be. With that done, we can now go ahead and take the hole saw and cut out the larger hole to fit the seven pull connector. more
2/1/2013 4:30:42 AM
Fifth Wheel and Gooseneck Wiring Harness Installation - 2012 Dodge Ram- Video
Today on our 2012 Dodge Ram 2500, we are going to be installing the Pollock fifth wheel and gooseneck T-Connector with seven-pole wiring part number PK11893-11932. First, we need to begin by finding a suitable location for our seven-pole in the bed. Just here past the cut out in the bed behind the drivers side wheel well is where we are going to mount our sub pole connector. First step will be drilling a pilot hole. Ill take my eight-inch bit which will be the same as the pilot hole for hole saw that we will need to cut out. Now I can go underneath and check to make sure its not going to run into anything. more
8/9/2012 7:02:52 AM
Trailer Wiring Harness Installation - 2011 Dodge Ram- Video
Today on our 2011 Dodge Ram well be installing the Pollak fifth wheel and goose neck connector wiring harness part #: PK11932. First well need to locate a suitable spot for installing the connector in the truck bed. Then Ill take a pilot bit and run it through the bed and double check my location. Were going to go ahead and take a quarter inch bit which will be the same size as my pilot bit for my hole saw and drill out the hole. Now with my hole drilled out well go ahead and take the hole saw and make it large enough for the connector to fit through. With the large hole drilled out we can now take the wiring harness and feed it from underneath through the hole. more
5/31/2012 1:33:17 PM
Trailer Wiring Harness Installation - 2001 Dodge Ram- Video
Today on this 2001 Dodge Ram pickup 1500 were gonna install part number 118329 from Tow Ready. This is a 4-pole wiring harness. Alright well go ahead and show you where the connection points are if were looking at the driver side of the vehicle it will be right behind the bumper and this is our first connection point right here. inaudible you got to push in that way and you can pull it apart. inaudible the 2 pieces well install the T-connector with the yellow wire, then well route this wire and the 4-pole wire over to the center of the hitch. Well do that by following the factory wire harness inaudible with the green wire and were now on over to the other side. more
12/29/2011 2:07:49 PM
Fifth Wheel and Gooseneck Wiring Harness Installation - 2004 Dodge Ram 3500- Video
Today on this 2004 Dodge 3500, we are going to install the pre-wired fifth wheel trailer connect that mounts in the pickup bed, part number 51-97-411. Start by looking for a spot to install our assembly connector. We are going to mount ours here, just behind the wheel well in the pickup bed. Using a 1/4 inch bit we will make a pilot hole so that we can use our hole saw bit to drill out a 2 inch hole so that we can mount our connector. Now you can leave your drill bit in the hole, go underneath and check to make sure you have enough clearance to fit your 7 way wiring through. Now we will go ahead and drill it out with our 2 inch hole saw bit. more
10/20/2011 6:58:20 AM
Trailer Brake Controller Installation - 1999 Dodge Ram Pickup- Video
Today on this 1999 Dodge 1500 Pickup, we are going to install part number 90185 Prodigy Brake controller. We are also going to install this T-1 harness part number 118329 from Tow Ready and we are going to install this brake controller also with part number ETBC7. First off we are going to start off installing the part of the T-1 wiring harness part number 118329. We need to do that so our ETBC7 has a 4-pole to plug into. The connection points are underneath the tail light over here. What we are going to do is push the button on top and pull down the bottom and it will come apart. And we are working on the passenger side. On the passenger side we will install the connector with the green wire. All right, we will go ahead and route our 4-pole wire over to the center and then we will run our yellow wire, run that over past the center to the driver side tail light and we will make the same connection underneath the driver side tail light. more
10/7/2009 1:16:46 PM
Filter Videos
Filter Videos
